Prepare for UPSC Indian Engineering Services (IES/ESE) with verified solutions across Analog & Digital Communications, VLSI & Semiconductor Devices, Signals & Systems, Electromagnetics & Antennas, Microwave Engineering, Control Systems, Computer Organization, and Network Theory.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
Consider the following statements regarding semiconductors:
1. At room temperature, there are approximately $1.5 \times 10^{10}$ free carriers in a cubic centimeter of intrinsic silicon material.
2. The free electrons in the intrinsic material are only due to the natural causes and are referred to as intrinsic carriers.
3. The ratio of the number of carriers in germanium to that of silicon is greater than $10^5$.
Which of the above statements are correct?
Consider the following statements regarding semiconductor diodes:
1. PIV ratings for silicon diodes can be in the neighborhood of $400\text{ V}$, whereas the maximum value for germanium is closer to $600\text{ V}$.
2. Silicon can be used for applications in which the temperature may rise to about $300^{\circ}\text{C}$.
3. Germanium has a much lower maximum rating ($100^{\circ}\text{C}$).
Which of the above statements are not correct?
In P-N junction diode, the factor $r_B$ (resistance of the semiconductor material itself and the resistance introduced by the connection between the semiconductor material and the external metallic conductor) can range from typically
Consider the following statements regarding transistor amplifier:
1. Current gain increases with increase in temperature.
2. $|V_{BE}|$ (base-emitter voltage) decreases about $100\text{ mV}$ per degree Celsius increase in temperature.
3. Reverse saturation current doubles in value for every $10^{\circ}\text{C}$ increase in temperature.
Which of the above statements are correct?
Consider the following statements regarding transistors :
1. Networks that are quite stable and relatively insensitive to temperature variations have high stability factors.
2. Higher the stability factor, more sensitive is the network to variations in that parameter.
3. For the emitter-bias configuration, the stability factor $S(I_{CO}) = \beta + 1$ (for $R_B / R_E \gg \beta + 1$).
Which of the above statements are correct?
Consider the following statements regarding JFET :
1. The level of $V_{GS}$ that results in $I_D = 0\text{ (zero) mA}$ is defined by $V_{GS} = V_P$.
2. In ohmic region, JFET can actually be employed as a variable resistor.
3. In n-channel JFET, for all levels of $V_{GS}$ between $0\text{ (zero) V}$ and the pinch-off level, the current $I_D$ will range between $I_{DSS}$ (maximum current) and $0\text{ (zero) A}$, respectively.
Which of the above statements are correct?
The efficiency of a class B amplifier for a supply voltage of $V_{CC} = 24\text{ V}$ with peak output voltage of $V_L(p) = 6\text{ V}$ is
Consider the following statements regarding clamper circuit:
1. The network must have a capacitor, a diode and a resistive element, but it can also employ an independent DC supply to introduce an additional shift.
2. The total swing of the output is equal to the total swing of the input signal.
3. During the period when the diode is in the 'on' state, the capacitor will hold on to its established voltage level.
Which of the above statements are correct?
Consider the following statements regarding MOSFETS/VMOS FETS:
1. Compared with commercially available planar MOSFETs, VMOS FETs (Vertical Metal-Oxide-Silicon FETs) have reduced channel resistance levels and higher current and power ratings.
2. VMOS FETs have a negative temperature coefficient that will combat the possibility of thermal runaway.
3. The reduced charge storage levels result in faster switching times for VMOS construction compared to those for conventional planar construction.
Which of the above statements are correct?
Consider the following statements regarding MOSFETS:
1. For the values of $V_{GS}$ less than the threshold level, the drain current of an enhancement-type MOSFET is $0\text{ (zero) mA}$.
2. For the levels of $V_{GS} \le V_T$, the drain current is related to the applied gate-to-source voltage by the non-linear relationship $I_D = k(V_{GS} - V_T)^2$.
3. The $k$ term is a constant that is a function of the construction of the device. The value of $k$ can be determined from the equation
$$k = \frac{I_{D(\text{on})}}{(V_{GS(\text{on})} - V_T)^2}$$
where $I_{D(\text{on})}$ and $V_{GS(\text{on})}$ are the values for each at a particular point on the characteristics of the device.
Which of the above statements are correct?
If the input voltages of an op-amp are $V_{i1} = 150\ \mu\text{V}$, $V_{i2} = 140\ \mu\text{V}$, the differential gain is $4000$ and $\text{CMRR}$ is $100$, then the output voltage is
An inverting amplifier using op-amp is having $R_F = 150\text{ k}\Omega$ and $R_1 = 2\text{ k}\Omega$. The offset voltage for the op-amp specification listing $I_{IO} = 100\text{ nA}$ is
Among two cubes, the first one has a length of $L\text{ m}$, while the second one has a length of $2L\text{ m}$. What is the ratio of the conductivities of the materials of the cubes so that the resistance between any two faces of one cube is same as that of the other cube?
A resistor is made up of alloy 1 dissipating $50\text{ W}$ of electrical power at $110\text{ V}$ at $20^{\circ}\text{C}$. Another resistance of alloy 2 is made having the same resistance as the first resistor but consuming double amount of the power of the first one. If the temperature remains constant during the entire process, then the current flowing through alloy 2 resistor at $20^{\circ}\text{C}$ is
Consider the following statements regarding DC network analysis:
1. A voltage source with a parallel resistance can be converted into a current source with a series resistance.
2. A constant current source of $I$ and a parallel resistance $R$ can be converted into a constant voltage source of voltage $V (= IR)$ and a resistance $R$ in series with it.
3. Dependent sources are parts of models which are used to represent electrical properties of electronic devices.
Which of the above statements are correct?
The Curie temperature of nickel (Ni) metal is
Consider the following statements regarding electromagnetic induction:
1. Whenever magnetic flux linked with a closed coil changes, an induced EMF is set up in the coil and the induced EMF lasts as long as the change in magnetic flux continues.
2. The magnitude of the induced EMF is proportional to the rate of change of magnetic lines of force.
3. Lenz's law states that the direction of the induced current is such that it opposes the very cause producing this current.
Which of the above statements are correct?
A current of $10\text{ A}$ when flowing through a coil of $2000$ turns establishes a flux of $0.6\text{ milliweber}$. The inductance of the coil is
Consider the following statements regarding autotransformer:
1. Voltage regulation of an autotransformer is better because of reduced voltage drop in the resistance and reactance.
2. An autotransformer has variable output voltage, when a sliding contact is used for the secondary.
3. Short-circuit current is larger for an autotransformer due to reduced internal impedance.
Which of the above statements are correct?
Consider the following statements regarding transformer cooling methods:
1. In air blast cooling method of transformers, continuous blast of filtered air is forced through the core and windings for better cooling.
2. In oil blast cooling, forced air is passed over cooling elements of transformer immersed in oil.
3. In forced oil and water cooling, metallic tubes are situated inside the tank, below the oil level. Water is circulated through these tubes to extract heat from oil.
Which of the above statements are correct?
Consider the following statements regarding DC machines:
1. Commutation is the process of producing a unidirectional or direct current from the alternating current generated in the armature coil.
2. The main cause of sparking at the commutator being the reactance voltage, it can be minimized by using high-resistance carbon brushes.
3. Armature reaction AT (Ampere-turns) in DC machines can be compensated by placing a compensating winding in the pole faces with its axis along the brush axis and excited by the armature current in series connection, so that it causes cancellation of armature reaction AT at all values of armature current.
Which of the above statements are correct?
Consider the following statements regarding electric circuits:
1. A 60% lagging power factor implies an inductive load in which the supply current lags the voltage by an angle with a cosine of 0.6 (i.e., by approximately 53°).
2. A 90% leading power factor would indicate a capacitive load in which the voltage leads the current by an angle with a cosine of 0.9 or approximately 26°.
3. When the phase angle (angle between supply voltage and current) is zero, then all of the apparent power from the supply is dissipated as true power in the load.
Which of the above statements are correct?
Consider the following statements regarding Blondel's theorem for measurement of power in a polyphase system:
1. If a network is supplied through $N$ conductors, the total power is measured by summing the reading of $N$ wattmeters so arranged that a current element of a wattmeter is in each line and corresponding voltage element is connected between that line and a common point.
2. If the common point is located on one of the lines, then the power may be measured by $(N - 1)$ wattmeters.
3. The most common applications of Blondel's theorem include the two-wattmeter method of measurement of power in 3-phase, 3-wire load circuits and three-wattmeter method of measurement of power in 3-phase, 4-wire load circuits.
Which of the above statements are correct?
Consider the following statements regarding cells and batteries:
1. A manganese-alkaline cell can sustain a constant terminal voltage for heavy loads over a much longer period of time than the less expensive zinc-carbon cell.
2. The major advantage of manganese-alkaline cell is that its terminal voltage is maintained constant for much longer periods than either the mercury or zinc-carbon cells.
3. The mercury cell is a modification of the zinc-carbon cell, in which mercuric oxide is used as the negative electrode.
Which of the above statements are not correct?
A battery with a rating of $300\text{ Ah}$ is to be charged. If the internal resistance of the battery is $0.008\ \Omega$, the safe maximum charging current of the battery is $37.5\text{ A}$ and its (discharged) terminal voltage is $11.5\text{ V}$, then the initial output voltage level for the battery charger is