Prepare for UPSC Indian Engineering Services (IES/ESE) with verified solutions across Analog & Digital Communications, VLSI & Semiconductor Devices, Signals & Systems, Electromagnetics & Antennas, Microwave Engineering, Control Systems, Computer Organization, and Network Theory.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
Consider the following statements regarding CMOS fabrications:
1. n-well CMOS circuits are superior to p-well because of the lower substrate bias effects on transistor threshold voltage and inherently lower parasitic capacitances associated with source and drain regions.
2. Latch-up problems can be considerably reduced by using a low-resistivity epitaxial p-type substrate as the starting material, which can subsequently act as a very low-resistance ground plane to collect substrate currents.
3. The twin-tub fabrication process allows separate optimization of the n- and p-transistors.
Which of the above statements are correct?
Consider the following statements regarding CMOS and bipolar technologies:
1. Bipolar technologies are having high delay sensitivity to load as compared to CMOS technologies.
2. CMOS technologies are having low drive current as compared to bipolar technologies.
3. CMOS technologies are having low power dissipation as compared to bipolar technologies.
Which of the above statements are correct?
Which one of the following approaches is used to reduce the area per bit requirement which basically consists of a capacitor $C_m$, which can be charged during 'write' from the 'read/write' line, provided that the 'row select' line is Hi?
The microprocessor Zilog Z8000 is a/an
The execution of ORI instruction requires
Which one of the following instructions in 8085 microprocessor does not affect any flag?
Consider the following statements regarding RISC processor:
1. The number of instructions is less than 400.
2. The number of addressing modes is more than 3.
3. Memory is accessed only by Load and Store instructions.
Which of the above statements are not correct?
Consider the following statements regarding MC68HC11 microcontroller :
1. It has 40 I/O lines with multiple functions.
2. It has two operating modes.
3. It has 8k bytes of ROM and 512 bytes of EEPROM.
Which of the above statements are correct?
The Z-transform of $x(n) = -a^n u(-n - 1)$ is
The inverse Z-transform of $X(z) = \log(1 + az^{-1})$ with ROC $|z| > |a|$ is
Consider the following statements regarding Z-transform:
1. The ROC of anti-causal signal is the interior of a circle of some radius $r_1$.
2. If $x(n)$ is anti-causal, then $x(0) = \lim_{z \to \infty} X(z)$.
3. The ROC of correlation of two sequences $x_1(n)$ and $x_2(n)$ is at least the intersection of the ROC of $X_1(z)$ and $X_2(z^{-1})$.
Which of the above statements are correct?
Consider the following statements regarding FIR filters:
1. FIR filters are sometimes called moving-average filters.
2. Because of the linear-phase requirements, the zeros of the transfer function must lie inside the unit circle in the $z$-plane.
3. The linear-phase characteristic makes the time delay of the filter equal to half its length, which may be large.
Which of the above statements are correct?
Consider a multimode step-index optical fiber that has a core radius of $25\ \mu\text{m}$, a core index of $1.48$ and an index difference $\Delta = 0.01$. What is the $V$-number at an operating wavelength of $840\text{ nm}$?
Match the following Lists:
| List-I | List-II |
|---|---|
| P. Perigee | 1. It is the point on the orbit that is nearest to the center of the Earth. |
| Q. Eccentricity | 2. It is the point on the satellite orbit that is at the farthest distance from the center of the Earth. |
| R. Semi-major axis | 3. It is the ratio of the distance between the center of the ellipse and the center of the Earth to the semi-major axis of the ellipse. |
| S. Apogee | 4. It is a geometrical parameter of an elliptical orbit. |
Select the correct answer using the code given below.
An Earth station antenna having a maximum gain of $60\text{ dB}$ at the operational frequency is fed from a power amplifier generating $10\text{ kW}$. If the feed system has a loss of $2\text{ dB}$, what is the Earth station EIRP?
Consider the following statements related to optical fiber :
1. Multimode step-index fibers are ideally suited for high-bandwidth, very long-haul applications.
2. Single-mode fibers are generally used on lower bandwidth, shorter haul applications using single-mode injection lasers.
Which of the above statements is/are correct?
Match the following Lists:
| List-I | List-II |
|---|---|
| P. Virtual circuit packet switching | 1. No dedicated path |
| Q. Datagram packet switching | 2. Fixed bandwidth |
| R. Circuit switching | 3. Route established for each packet |
Select the correct answer using the code given below.
Consider the following statements related to CDMA:
1. Because spread spectrum is obtained by the use of noise-like signals, where each user has a unique code, privacy is inherent.
2. The signals closer to the receiver are received with less attenuation than the signals farther away.
Which of the above statements is/are correct?
If A and B choose $p = 47$, $g = 3$, and A picks a random number $x = 8$ and B picks a random number $y = 10$, what are the secret keys for A and B, respectively, using the Diffie-Hellman key exchange algorithm?
Which one of the following is the CRC code for the data word $110101010$ using the divisor $10101$?
A host is connected to 16 synchronous terminals through a pair of statistical time-division multiplexers utilizing the bit-map multiplexing. The sixteen asynchronous terminal ports operate at $1200\text{ bps}$. The line port has a bit rate of $9600\text{ bps}$. The data link control protocol is HDLC. What are the maximum line utilization efficiency and throughput, respectively?
The bandwidth of QASK signal is
CSMA stands for
The attenuation in optical communication is usually expressed in decibels per unit length as
Match the following Lists:
| List-I | List-II |
|---|---|
| P. IP layer | 1. Transmission of bits |
| Q. TCP/UDP layer | 2. Network layer of the OSI reference model |
| R. Application layer protocols | 3. Transport layer of the OSI reference model |
| S. Physical layer | 4. Application layer of the OSI reference model |
Select the correct answer using the code given below.