Prepare for UPSC Indian Engineering Services (IES/ESE) with official previous years' questions, detailed derivations, IS Code references, and step-by-step structural calculations across Structural Analysis, Soil Mechanics & Foundation Engineering, Fluid Mechanics & Hydraulics, RCC & Steel Structures, Surveying, Environmental Engineering, and Transportation.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
Water absorption for burnt clay heavy duty bricks should not be more than :
The decomposition of felspar is represented as $\text{K}_2\text{O}\cdot\text{Al}_2\text{O}_3\cdot 6\text{SiO}_2 + \text{CO}_2 + n\text{H}_2\text{O} =$
The metal oxide used to make emerald green glass is:
Match the following lists:
| List-I | List-II |
|---|---|
| P. Cupping | 1. Caused by wood limbs encased by wood of the tree trunk |
| Q. Bowing | 2. Caused by grain irregularities in the board |
| R. Checks | 3. Small cracks appearing at the ends of boards due to rapid drying |
| S. Knots | 4. Unequal shrinking in the radial and tangential direction |
Select the correct answer using the code given below:
| Option | P | Q | R | S |
|---|---|---|---|---|
| (a) | 2 | 4 | 1 | 3 |
| (b) | 4 | 2 | 3 | 1 |
| (c) | 1 | 2 | 4 | 3 |
| (d) | 3 | 2 | 1 | 4 |
Which one of the following statements is not correct regarding the fineness of cement?
Match the following lists:
| List-I (Types of cement) | List-II (Uses) |
|---|---|
| P. Rapid hardening | 1. Repair of bridges |
| Q. Quick-setting | 2. Dams |
| R. High alumina | 3. Concrete under water |
| S. Low-heat | 4. Refractory concrete in industries |
Select the correct answer using the code given below:
The approximate composition of $\text{CaO}$ in Portland cement is in the range of:
The percentage of $\text{MgO}$ in cement is calculated using:
The minimum value of Modulus of Rupture for Class A lime should be :
Match the following lists:
| List-I (Cement mortar for different works) | List-II (Proportion of cement : Sand in mortar) |
|---|---|
| P. Normal brickwork | 1. $1 : 4$ |
| Q. Plastering work | 2. $1 : 3$ |
| R. Grouting cavernous rocks | 3. $1 : 6$ |
| S. Guniting | 4. $1 : 1.5$ |
Select the correct answer using the code given below:
Which one of the following statements is correct regarding the factors influencing strength of concrete?
The cement content in a mix design is $378\text{ kg/m}^3$, water content $170\text{ kg}$, sand is $30\%$ of total aggregate, entrapped air is $1\%$, specific gravity of cement, coarse aggregate and fine aggregate are, respectively $3.15$, $2.70$ and $2.60$. The fine aggregate is approximately :
The component of stress acting on infinitesimal element is shown in the figure. Which one of the following statements is not correct?
An element $2\text{ cm}$ long is extended to twice of its initial length and then compressed to its initial length. The engineering strains for the extension and compression are, respectively:
A rectangular block is subjected to two perpendicular stresses of $10\text{ MPa}$ tension and $10\text{ MPa}$ compression. What are the stresses on planes inclined at $45^{\circ}$ with the horizontal plane?
An element in plane stress is subjected to normal stresses $p_1 = 120\text{ N/mm}^2$ and $p_2 = 45\text{ N/mm}^2$ (both are tensile stresses) and shearing stress of $30\text{ N/mm}^2$ (simple shear). What is the normal stress ($p_n$) acting on an element rotated through an angle $45^{\circ}$?
At a point in an elastic material, a direct tensile stress of $70\text{ N/mm}^2$ and a direct compressive stress of $50\text{ N/mm}^2$ are applied on planes at right angles to each other. If the maximum principal stress in the material is limited to $75\text{ N/mm}^2$, what is the maximum shear stress?
A material has strength in tension, compression and shear as $30\text{ N/mm}^2$, $90\text{ N/mm}^2$ and $25\text{ N/mm}^2$, respectively. If a specimen of diameter $25\text{ mm}$ is tested in compression, then identify the failure load and failure plane.
A simply supported beam of span $3.0\text{ m}$ has a cross-section $120\text{ mm} \times 180\text{ mm}$. If the permissible stress in the material of the beam is $10\text{ N/mm}^2$, what is the maximum uniformly distributed load (UDL) that it can carry? (Ignore the moment due to self-weight)
A surveyor's steel tape $30\text{ m}$ long has a cross-section of $15\text{ mm} \times 0.75\text{ mm}$. With this, line $AB$ is measured as $150\text{ m}$. If the force applied during measurement is $120\text{ N}$ more than the force applied at the time of calibration, what is the actual length of the line? (Take the modulus of elasticity for steel as $200\text{ kN/mm}^2$)
The stepped bar shown in the figure is made up of two different materials. Material 1 has Young's modulus $= 2 \times 10^5\text{ N/mm}^2$, while that of Material 2 is $1 \times 10^5\text{ N/mm}^2$. What is the extension of the bar under a pull of $30\text{ kN}$ if both the portions are $20\text{ mm}$ in thickness? (The dimensions shown below are in $\text{mm}$)
Two parallel walls, $8\text{ m}$ apart, are stayed together by a steel rod of $20\text{ mm}$ diameter passing through metal plates and nuts at each end. The nuts are screwed up to the plates while the bar is at a temperature of $400\text{ K}$. What is the pull exerted by the bar after it has cooled to $300\text{ K}$, if the total yielding at the two ends is $5\text{ mm}$? (Take coefficient of thermal expansion for steel as $12 \times 10^{-6}\text{ per K}$ and Young's modulus of steel as $2 \times 10^5\text{ N/mm}^2$)
Which one of the following statements is not correct regarding principal stresses and planes?
What is the maximum torque $T_e$ that can be applied to a solid steel cylindrical shaft $8\text{ cm}$ in diameter, if the shaft is to remain elastic? (Take the elastic limit in shear and the shear modulus as $\tau_0 = 145\text{ MPa}$ and $G = 76\text{ GPa}$, respectively)
Given the state of stress $\sigma_x = \sigma_y = -\sigma_0$ (where $\sigma_0 > 0$) and $\tau_{xy} = 0\text{ (zero)}$ as shown in the figure, which one of the following statements is not correct?