Prepare for UPSC Indian Engineering Services (IES/ESE) with official previous years' questions, detailed derivations, IS Code references, and step-by-step structural calculations across Structural Analysis, Soil Mechanics & Foundation Engineering, Fluid Mechanics & Hydraulics, RCC & Steel Structures, Surveying, Environmental Engineering, and Transportation.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
If the standard deviation is $4\text{ N/mm}^2$ and the desired characteristic strength is $20\text{ N/mm}^2$; what is the mean strength of concrete?
As per IS 456:2000, what is the creep coefficient of concrete at the age of $28\text{ days}$ of loading?
As per IS 875 (Part 2) 1987, what is the minimum imposed load that needs to be considered for living rooms?
What is the typical unit weight of brick masonry used by designers?
Which one of the following statements related to IS 875 (Part 3) - 1987 is not correct?
As per IS 875 (Part 2) 1987, what is the reduction in total distributed imposed load (in percent) for design of supporting structural elements in a structure with $10$ floors?
A one-way slab has effective span of $3.6\text{ m}$ and is $150\text{ mm}$ thick. The live load expected on it is $3\text{ kN/m}^2$. What is the load for checking serviceability?
As per IS 456:2000, the strength of concrete achieved in structure is taken as:
As per IS 456:2000, which one of the following statements is not correct?
As per IS 1893:2016, what is the value of constant '$A$' in the equation mentioned below for determining cyclic stress ratio ($CSR$)?
$CSR = A \left(\frac{a_{\max}}{g}\right) \left(\frac{\sigma_{vo}}{\sigma'_{vo}}\right) r_d$
where, $a_{\max} =$ Peak ground acceleration ($PGA$) preferably in terms of $g$, $g =$ acceleration due to gravity, $r_d =$ stress reduction factor.
As per IS 1893:2016, what is the percentage of imposed load to be considered in the calculation of seismic weight, if the imposed uniformly distributed floor load is $4\text{ kN/m}^2$?
Which one of the following statements is not correct regarding the response reduction factor?
Which one of the following statements is not correct regarding the working stress method?
As per IS 800:2007, the maximum effective slenderness ratio for 'members always in tension (other than pre-tensioned members)' is:
What is the net area for the tension member shown in the figure, in case of punched holes?
What is the design tensile strength of the plate $130\text{ mm} \times 12\text{ mm}$ with holes for $16\text{ mm}$ diameter bolts by considering yielding of gross section? (Take $f_y = 250\text{ N/mm}^2$ and $\gamma_{m0} = 1.1$)
Consider the following statements:
The design strength of a tension member is the lowest of:
Which of the above statements are correct?
As per IS 800:2007, what is the effective length of prismatic compression member for the restrained (both in translation and rotation) boundary conditions at both the ends? (Take $L$ as actual length of the member)
What is the working load of a compression member with effective sectional area as $7500\text{ mm}^2$ and design compressive stress of $300\text{ N/mm}^2$? (Take factor of safety $(\text{FoS}) = 1.5$)
Which one of the following statements related to design of laced columns as per IS 800:2007 is not correct?
A roof of a hall measuring $8\text{ m} \times 12\text{ m}$ consists of $100\text{ mm}$ thick reinforced concrete slab supported on I-beams spaced $3\text{ m}$ apart. The steel beam is designed considering finishing load of $1.5\text{ kN/m}^2$ and live load of $1.5\text{ kN/m}^2$. What is the permissible deflection for this beam as per IS 800:2007, by considering effective length of beam as $9\text{ m}$?
A simply supported beam of effective span $1.5\text{ m}$ is carrying a factored concentrated load of $360\text{ kN}$ at mid span. What is the section modulus of the beam? (Take $f_y = 250\text{ N/mm}^2$ and $\gamma_{m0} = 1.1$)
What is the effective length of a simply supported beam of span length $7\text{ m}$ for the following restraint conditions at the support under normal loading conditions?
Torsional restraint: Fully restrained;
Warping restraint: Both the flanges fully restrained
What is the bending moment in case of continuous purlins? (Take the effective length of the purlin as $L$ and load intensity as $w$)
In the case of stiffened seated connection, to avoid local buckling, typically the ratio of outstanding leg length to its thickness should be: