Prepare for UPSC Indian Engineering Services (IES/ESE) with verified solutions across Analog & Digital Communications, VLSI & Semiconductor Devices, Signals & Systems, Electromagnetics & Antennas, Microwave Engineering, Control Systems, Computer Organization, and Network Theory.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
A variation in the ambient humidity causes a variation in the resistance of the element that is usually mixture of:
The typical range of dissipation factor (D) of capacitor is:
Match the following lists:
| List-I | List-II |
|---|---|
| P. Square wave | 1. Less harmonics |
| Q. Triangular wave | 2. Made up of fundamental frequency plus an infinite number of odd harmonics |
| R. Two waveforms deliver same power to identical resistors | 3. RMS voltages must be the same |
Select the correct answer using the code given below:
One of the advantages of Ayrton shunt is that it eliminates the possibility of the meter movement being in the circuit:
The Poisson's ratio for most metals lies:
The relation among minimum detectable signal (MDS), IF bandwidth (BW) and noise figure (NF) of a spectrum analyzer is:
In the design of Digital IIR Filters by means of Bilinear Transform, the design specifications are given. Match the following lists:
| List-I | List-II |
|---|---|
| P. $N$ and $\Delta f$ fixed | 1. The design procedure has to start with the evaluation of the order of the filter necessary to meet the specifications in terms of the desired attenuation, transition bandwidth and pass-band deviation. |
| Q. $\Delta f$ and $\delta$ fixed | 2. The filter is completely specified and the transition bandwidth is directly obtainable during the design procedure. |
| R. $N$ and $\delta$ fixed | 3. The design is completely determined for the Butterworth filter case by obtaining the value of the attenuation at $f_a$ directly. |
Select the correct answer using the code given below:
In a rosette gauge, the angle between any two longitudinal gauge axes is:
A chopper-stabilized amplifier circuit eliminates the effects of:
The inductance of a 25 A electrodynamic ammeter changes uniformly at the rate of $0.0035\text{ mH/radian}$. The spring constant is $10^{-6}\text{ N}\cdot\text{m/radian}$. What is the angular deflection at full scale approximately?
What are the values of delta-connected branch resistances $R_{ab}$, $R_{bc}$ and $R_{ca}$ of the star-connected network shown in the figure using star to delta transformation respectively?
What is the value of number of possible trees of the graph shown in the figure?
Which one of the following is a fundamental cut set of the graph shown in the figure?
For the network shown in the figure if the switch is closed at $t=0\text{ (zero)}$, and when $\frac{R}{2L} < \frac{1}{\sqrt{LC}}$; which one of the following statements is correct?
An R-L-C series circuit has $R = 4\;\Omega$, $L = 2\text{ H}$ and $C = 2\text{ F}$. What type of transient current response is offered by the circuit for step function voltage input?
What is the value of $v_o(t)$ for the circuit shown in the figure, assuming zero initial conditions?
What is the Laplace transform of the periodic waveform shown in the figure, where $a=1$, $2a=2$, $3a=3$ and $4a=4$?
For the network shown in the figure, the switch is moved from $a$ to $b$ at $t = 0^-$. What is the value of voltage $v(t)$?
What is the voltage transfer function of the two-port network shown in the figure?
The Z-parameters of a two-port network are $Z_{11} = 2\;\Omega$, $Z_{12} = 1\;\Omega$, $Z_{21} = 10\;\Omega$ and $Z_{22} = 11\;\Omega$. The corresponding values of hybrid parameters are:
What are the lattice equivalent network parameters $Z_A$ and $Z_B$ of a symmetrical $\pi$ network shown in the figure?
What is the Thevenin equivalent impedance of the circuit shown in the figure?
What is the maximum conversion time for an n-bit counting ADC?
If a square wave is impressed upon either a point contact or a p-n junction germanium diode, the resistance does not change instantaneously from its forward value to its back value, or vice versa. Which one of the following is required for this change to take place?
By considering standard notations, the time period of a linear ramp generator in 555 timer is: