Prepare for UPSC Indian Engineering Services (IES/ESE) with verified solutions across Analog & Digital Communications, VLSI & Semiconductor Devices, Signals & Systems, Electromagnetics & Antennas, Microwave Engineering, Control Systems, Computer Organization, and Network Theory.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
Five channels, each with a 100 kHz bandwidth, are to be multiplexed together. If there is a need for a guard band of 10 kHz between the channels to prevent interference, the minimum bandwidth of the link will be
The entries in a CIDR routing table contain 32-bit IP address and a 32-bit mask. The CIDR enables a technique called
The free space path loss $L_p$ incurred by an electromagnetic wave is
Which one of the following amplifiers is widely used in transponders to provide the final output power required to the transmit antenna?
Which one of the following systems of satellites is sometimes called 'Internet in the Sky'?
A directional antenna with 10 dB gain radiates 500 watts. The receiving antenna at 15 km distance receives 2 microwatt. If there is a negligible ground and ionospheric reflection, the effective area of the receiving antenna will be nearly
The time used for all civil timekeeping purposes, and is the time reference which is broadcast by the National Bureau of Standards as a standard for setting clocks, is
The point on the earth vertically under the satellite is referred to as the
The total reduction of power level in optical fiber cable, A(dB) is
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): Stokes' theorem gives relation between a double integral and a single integral, and is applied only to an open surface.
Statement (II): Gauss' divergence theorem gives relation between a triple integral and a double integral, and is applied only to a closed surface.
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): The microwave junction can be defined as S-parameters or scattering parameters.
Statement (II): A scattering matrix is a square matrix which gives all the combinations of power relationships between the various input and output ports of a microwave junction.
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): Electron lithography offers higher resolution than optical lithography.
Statement (II): Electron lithography has small wavelength of the 10-50 keV electrons.
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): In communication network, the element of the network should be designed such that maximum power transfer takes place between the source to the load.
Statement (II): The maximum power is absorbed by one network from another network, when the impedance of one is the complex conjugate of the other.
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): A network is two or more devices connected together through links.
Statement (II): A link is a communication pathway that transfers data from one device to another.
Directions: The following item consists of two statements, one labelled as 'Statement (I)' and the other as 'Statement (II)'. Examine these two statements carefully and select the correct code.
Statement (I): Mode partition noise is a multiplicative noise in an optical fiber link.
Statement (II): Mode partition noise arises when the optical source emits several frequencies in a rapid succession.
A transistor with $\alpha=0.98$ and $I_{CBO}=5\ \mu\text{A}$ is biased, so that $I_{BQ}=100\ \mu\text{A}$. What is the leakage current $I_{CEO}$?
Which one of the following is correct for the circuit shown below?
Consider the following statements regarding essential characteristics of a practical op-amp:
1. The open-loop voltage gain $A_{OL}$ is negatively infinite.
2. The input impedance between terminals 1 and 2 is infinitely large and the input current is zero.
3. The output impedance is zero and the output voltage is independent of the load.
Which of the above statements are correct?
Consider the following statements regarding common collector configuration
1. The common-collector configuration is used primarily for impedance-matching purposes.
2. It has a high input impedance and low output impedance, opposite to that of the common-base configuration.
3. A common-collector circuit configuration is provided with the load resistor connected from emitter to ground.
Which of the above statements are correct?
$I_{DSS}$ is the maximum drain current for a JFET and is defined by the conditions
In which one of the following is it used that the particular operating wavelength can be selected at the time of device fabrication by an appropriate choice of the reflector spacing?
Consider the following statements for an edge-emitting laser:
1. For small threshold current, $d$ should be small to make the best use of the material gain.
2. A thick low band gap active region (large $d$) leads to increased losses by internal absorption $\alpha_{i}$.
3. For large material gain, the quantum well thickness should be large.
4. Absorption losses are often caused by absorption in the high band gap outer barriers forming the waveguide.
Which of the above statements are correct?
A $10\text{ V}$, $50\text{ Hz}$ sawtooth wave is pulse width modulated by a $4\text{ V}$ signal. What are the outputs for high time and duty cycle respectively?
Which one of the following is correct regarding channel length modulation?
In the design of the fixed-bias transistor circuit shown in the figure, what are the values of $R_{C}$ and $R_{B}$ respectively for a Q-point of $I_{C}=6\text{ mA}$ and $V_{CE}=4\text{ V}$, the transistor forward current gain is $\beta_{F}=200$ with a negligible $\beta_{R}$, $V_{BE}=0.7\text{ V}$?