Prepare for UPSC Indian Engineering Services (IES/ESE) with verified solutions across Analog & Digital Communications, VLSI & Semiconductor Devices, Signals & Systems, Electromagnetics & Antennas, Microwave Engineering, Control Systems, Computer Organization, and Network Theory.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
The mean time between failures and the mean failure rate if 100 faults were recorded for 300 transducers of a system during 1.5 years, the mean down time being 1 day, are respectively
A potentiometer is used to measure the displacement of a hydraulic ram. The potentiometer is 25 cm long, has a total resistance of 2500 ohms and is operating at 4 W with a voltage source. If it has linear resistance-displacement characteristics, then the sensitivity of the potentiometer (without loading effect) is
Assume we have a computer where the clocks per instruction (CPI) is 1.0 when all memory accesses hit in the cache. The only data accesses are loads and stores, and these total 50% of the instructions. If the miss penalty is 25 clock cycles and the miss rate is 2%, how much faster would the computer be if all instructions were cache hits?
Which one of the following is not correct when one goes down a memory hierarchy?
Which one of the following is the disadvantage of the software pole ?
Which one of the following is not related to the CISC architecture?
Which one of the following steps is not correct for an asynchronous data transfer?
In deadlock condition, at least one resource must be held in a non-shareable mode; that is, only one process at a time can use the resource. If another process requests that resource, the requesting process must be delayed until the resource has been released. This is called
Which one of the following statements is not correct for a buffer?
In a program, the following declaration :float number1, number2, sum, average;
is represented as
Which one of the following is not correct about Rambus DRAM?
Non-uniform memory access belongs to
What single-precision number does the following 32-bit word represent?
11000000101000000000000000000000
A better measure of memory-hierarchy performance is the average time to access memory. This can be represented as
Which of the following are used to make a decision that determines the program flow, based on ALU results or the contents of register?
Consider the following statements regarding the LVDT:
1. The LVDT output is basically an amplitude modulated signal. There is a possibility of a mix-up between the modulation frequency and the carrier frequency when the displacement varies sinusoidally.
2. Linearity is good up to 10 mm.
3. Sensitivity is high, approximately 80 V/m.
Which of the above statements are not correct?
Consider the following statements regarding filled system thermometers:
1. In case of system failure, usually the entire unit needs to be replaced.
2. Capillary allows considerable separation between the point of measurement and the point of indication.
3. Complex design makes them expansive.
Which of the above statements are correct?
Consider the following statements regarding the vibrating element pressure transducer :
1. It generates an inherently digital signal which is amenable to its acquisition by the microprocessor-based instrumentation.
2. It is sensitive to temperature variation, shock and vibration.
3. The detectable pressure range is typically from 10 mm of Hg to 6000 psig (42 MPa) with a typical accuracy of 0-1% of the span.
Which of the above statements are correct?
Consider the following statements regarding electromagnetic flowmeter:
1. It is not suitable for metering corrosive acids, cement slurries, detergents, greasy and sticky fluids.
2. It can measure high flow rates.
3. The liquid has to be conducting (conductivity > $10^{-6}\text{ mho-cm}$); this requirement eliminates its use for all gases and for most of the hydrocarbons.
Which of the above statements is/are not correct?
Consider the following statements regarding transducers:
1. Eddy-current gauge is used to measure the displacement.
2. Pirani gauge is used for high pressure.
3. Wiedemann effect is used in transducers to measure the torque, force, displacement and level measurement.
Which of the above statements are correct?
For the two-port network given below, what is the transfer impedance $(Z_{21})$?
For the network shown below, what is the voltage $v_{0}(t)$ across the resistor R, the switch closes at $t=0$, and assume all initial conditions are zero at $t=0$?
Consider the following statements regarding the semiconductor diode:
1. PIV rating for the silicon is near about 1000 V.
2. Maximum PIV rating for the germanium is closer to 200 V.
3. Germanium can be used for applications in which the temperature may rise to about $200^{\circ}\text{C}$.
Which of the above statements are not correct?
Consider the following statements regarding the semiconductor diode:
1. Ac or dynamic resistance can be defined as $r_{d} = \frac{26\text{ mV}}{I_{d}}$
2. The lower the Q-point of operation, the lower is the ac resistance.
3. As with the dc and ac resistance levels, the lower the level of currents used to determine the average resistance, the higher is the resistance level.
Which of the above statements are correct?
Consider the following statements regarding the BJT:
1. In the dc mode, the levels of $I_{\text{E}}$ and $I_{\text{C}}$ due to majority carriers are related by a quantity called alpha and defined by $\alpha_{\text{dc}} = \frac{I_{\text{C}}}{I_{\text{E}}}$.
2. In the case of ac mode, alpha is formally called the common-base, forward current amplification factor.
3. For linear (least distortion) amplification purpose, cutoff for the common-emitter configuration will be defined by $I_{\text{C}} = I_{\text{CEO}}$.
Which of the above statements are correct?