Prepare for UPSC Indian Engineering Services (IES/ESE) with official previous years' questions, detailed derivations, IS Code references, and step-by-step structural calculations across Structural Analysis, Soil Mechanics & Foundation Engineering, Fluid Mechanics & Hydraulics, RCC & Steel Structures, Surveying, Environmental Engineering, and Transportation.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
'Rind gall' of sapwood is characterized by
Which one of the following is correct with respect to incident in the context of construction safety?
For a concrete mix design, an estimation of water content corresponds to
For maximum strength, the desired workability of fresh concrete can be attained by which one of the following measures?
Plywoods are classified as Boiling Water Resistant (BWR) grade and Moisture Resistant (MR) grade depending on
High percentage presence of free silica in lime exhibits
Which one of the following is the correct sequence in increasing order for the chemical composition of Portland cement?
As per the straight line method, what is the annual depreciation value of an equipment that has delivered price of $1,00,000$ and has a residual value of $10\%$ of delivered price? Assume the ownership period as $5\text{ years}$.
Sugar added to cement mortar
Which one of the following is not the correct characteristic of an ideal mortar?
Surkhi is added to lime mortar for furnishing
A power plant has a stack with a diameter of $2\text{ m}$ and emits gases with a stack exit velocity of $15\text{ m/s}$ and a heat emission rate of $4900\text{ kJ/s}$. The wind speed is $5\text{ m/s}$. Stability is neutral. If the stack has a geometric height of $40\text{ m}$, what is the effective stack height, nearly?
A steel punch can be stressed to maximum compressive stress of $800\text{ MN/m}^2$. If the ultimate shear strength is $300\text{ MN/m}^2$, the least diameter of the hole that can be punched through a steel plate of $14\text{ mm}$ thickness will be
A bar of $2500\text{ mm}^2$ cross-sectional area is subjected to an axial load of $150\text{ kN}$. The extension over a gauge length of $100\text{ mm}$ is $0.05\text{ mm}$. If the decrease in each side is $0.00625\text{ mm}$, the value of Poisson's ratio is
The resilience in simple tension or compression is
where $\sigma$ is tensile or compressive stress, $A$ is area of cross-section and $E$ is modulus of elasticity.
Consider the following data:
Weight of a dish $= 48.6212\text{ g}$
$100\text{ mL}$ of sample is placed in the dish and evaporated. The new weight of the dish and dry solids $= 48.6432\text{ g}$
The dish is placed in a $550^{\circ}\text{C}$ furnace, then cooled. New weight $= 48.6300\text{ g}$
In this case, the total volatile solids are
The radius of the Mohr's circle of stress is
where $\sigma_x$ and $\sigma_y$ are normal stresses, and $\tau$ is shear stress.
Which one of the following statements is not correct regarding theories of failure?
The principal stresses at a point in an elastic material are $2\sigma$ tensile and $\sigma$ tensile. If an elastic limit in simple tension is $200\text{ N/mm}^2$, according to the maximum principal stress theory, the value of $\sigma$ at failure will be
In case of simple tension or compression, the maximum shear stress is equal to
For a general two-dimensional stress system, the maximum principal stress $\sigma_1$ is
where $\sigma_x$ and $\sigma_y$ are direct stresses on mutually perpendicular planes and $\tau_{xy}$ is shear stress on planes.
On a principal plane, the value of shear stress is
A circular log of timber has diameter $d$. The ratio of breadth $b$ to depth $h$ ($b : h$) of the rectangular beam that can be cut from a circular log for strongest section in bending is
The torsional stiffness $k$ is given by the relation
where $G$ is rigidity modulus, $J$ is polar moment of inertia and $l$ is length.
A cast iron main tube $800\text{ mm}$ in diameter carries water at pressure head of $100\text{ m}$. If the maximum permissible tensile stress is $20\text{ MN/m}^2$ and the weight of water is $10\text{ kN/m}^3$, the required thickness of the metal will be