Prepare for UPSC Indian Engineering Services (IES/ESE) with official previous years' questions, detailed derivations, IS Code references, and step-by-step structural calculations across Structural Analysis, Soil Mechanics & Foundation Engineering, Fluid Mechanics & Hydraulics, RCC & Steel Structures, Surveying, Environmental Engineering, and Transportation.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
A cylindrical air drum is $2.25\text{ m}$ in diameter with plates $1.2\text{ cm}$ thick. The efficiencies of the longitudinal and circumferential joints are $75\%$ and $40\%$ respectively. If the tensile stress in the plate is limited to $120\text{ MN/m}^2$, the safe maximum air pressure will be
The maximum shear stress $\tau_{\text{max}}$ for a beam of circular section is
where $A$ is cross-sectional area and $V$ is shear force.
Consider a rectangular hollow section having overall width $B$ and overall depth $D$, and let the width and depth of the symmetrically placed hole be $b$ and $d$ respectively. Then the section modulus ($Z$) is
A long rectangular wall is $2.5\text{ m}$ wide. The maximum wind pressure on the face of wall is $1.1\text{ kN/m}^2$ and the specific weight of masonry is $22\text{ kN/m}^3$. If the length of the wall is $1\text{ m}$, the maximum height of the wall so that there is no tension in the base of the wall will be nearly
A fixed beam of span $l$ is subjected to a central concentrated load $W$. The bending moment at the supports will be
In a fixed beam subjected to downward loads, the maximum bending moment is given by the greater fixing moment. This is true
The deflection $\delta$ at the free end of a cantilever is
where $P$ is point load at the free end, $EI$ is flexural rigidity and $L$ is length of the cantilever.
A cantilever beam of span $L$ is subjected to uniformly distributed load of intensity $W$. If the flexural rigidity is $EI$, the slope $\theta$ and deflection $\delta$ at the free end are respectively
The strain energy $U$ due to bending is
where $M$ is bending moment, $EI$ is flexural rigidity and $dx$ is short length of beam.
A rectangular beam $150\text{ mm} \times 240\text{ mm}$ deep is simply supported at the ends on a span of $4\text{ m}$ and carries a uniformly distributed load of $4\text{ kN/m}$ on the whole span. What is the point load at the centre it should carry so that the maximum deflection is doubled?
When a cable is passed over a pulley on the pier and is stayed at the back, the pier will be subjected to net horizontal force which is given by
where $H$ is horizontal tension in the cable, $\alpha$ is angle made by the cable with vertical and $\beta$ is angle made by the backstay with vertical at pier.
Which one of the following statements is not correct?
A steel chimney $3\text{ m}$ in diameter is situated in a region where the intensity of uniform wind pressure is $1200\text{ N/m}^2$. If the shape factor is $0.7$ and the intensity of wind pressure is uniform, the shear due to wind load at a level of $15\text{ m}$ below the top of the chimney will be
With regard to beams in structure, what are joists?
The design strength of a tension member due to the net section rupture for plates and threaded rods is
where $A_n$ is net effective area of cross-section, $f_u$ is ultimate strength of the material and $\gamma_{m1}$ is partial safety factor.
Which one of the following checks is necessary in the design of uniaxial bending?
The maximum slenderness ratio $\lambda$ for a member normally acting as a tie in a roof truss or a bracing system, but subject to possible reversal of stresses resulting from the action of wind or earthquake forces is
The permissible maximum shear stress $\tau_{vm}$ for a steel beam should not exceed
where $f_y$ is yield stress of steel.
As per IS 800:2007, the recommended value of an effective length for compression members of constant dimensions effectively held in position at both ends, but not restrained against rotation, is
Which one of the following is applicable in case of analysis of portal bracing?
The buckling of the web by diagonal compression can be prevented by which of the following?
Select the correct answer.
It is proposed to design an industrial building $12\text{ m}$ high for a $50$-year life. The building size is in the range $20\text{ m}$ to $50\text{ m}$, the topography of the site is practically plain and the terrain is in the city industrial area. If the risk coefficient $k_1 = 1$, terrain factor $k_2 = 0.9$, topography factor $k_3 = 1$ and wind speed $V_b = 47\text{ m/s}$, the design wind pressure at the site will be nearly
The ultimate tensile strain in steel is
The long-term deflections of reinforced concrete members under sustained loads are mainly due to
Select the correct answer.
The maximum spacing of vertical stirrups at beam ends (plastic hinge locations) as per IS 13920 is the lesser of