Prepare for UPSC Indian Engineering Services (IES/ESE) with official previous years' questions, detailed derivations, IS Code references, and step-by-step structural calculations across Structural Analysis, Soil Mechanics & Foundation Engineering, Fluid Mechanics & Hydraulics, RCC & Steel Structures, Surveying, Environmental Engineering, and Transportation.
Marking pattern: +2.00 positive, -0.66 negative (Official UPSC ESE 1/3rd Negative Marking Scheme; 150 Questions, 300 Marks).
Which of the following are the design steps of restrained slabs?
Select the correct answer.
Which of the following are the correct design requirements regarding underground water tanks?
Select the correct answer.
Which of the following characteristics are useful in the yield line patterns for slab with various boundary conditions?
Select the correct answer.
For cohesionless sand at a depth of $6\text{ m}$ and with an angle of internal friction of $30^{\circ}$, the active lateral pressure intensity will be (take unit weight of dry sand as $19600\text{ N/m}^3$)
A slab having total thickness $120\text{ mm}$ is provided reinforcement bars of following diameters. The permissible diameter is
The correct sequence of the stages for dressing of stone is
The short-term static modulus of elasticity $E_c$ for structural concrete defining the slope of the tangent to the stress-strain diagram may be estimated from
where $f_{ck}$ is the characteristic compressive strength of concrete.
The stone masonry construction is superior to brick masonry construction under which of the following circumstances?
Select the correct answer.
Consider the following statements:
The wall thickness depends upon
Which of the above statements are correct?
Grader may be used for the following works, except
What is the time required to grade and finish $30\text{ km}$ of road formation with width equal to thrice the width of the motor grader, using six passes of the motor grader with speed for each of the successive two passes as $6\text{ km/hr}$, $8\text{ km/hr}$ and $10\text{ km/hr}$ respectively? Assume machine efficiency based on operator's skill, machine characteristics and work conditions as $75\%$.
The factors influencing the output of a machine in construction are
Which of the above factors are correct?
Which one of the following statements is not correct in respect of network diagram for time scheduling techniques?
An interference float is defined as
What is the approximate efficiency of a Kaplan turbine developing $3000\text{ kW}$ under a net head of $5\text{ m}$? It is provided with a draft tube with its inlet (diameter $3\text{ m}$) set $1.6\text{ m}$ above the tailrace level. A vacuum gauge connected to the draft tube indicates a reading of $5\text{ m}$ of water. Assume draft tube efficiency as $68\%$ and acceleration due to gravity as $10\text{ m/s}^2$. Neglect head losses in draft tube.
Any cause which is beyond the control of the contractor or the owner, as the case may be, which they could not foresee or a reasonable amount of diligence could not have foreseen and which substantially affects the performance of the contract, is called
A point beyond which the project duration cannot be reduced irrespective of the increase in direct cost is known as
Which one of the following models has not been found to be of much practical value in the construction industry?
Which one of the following reasons is not correct for low labour productivity?
Consider the following basic causes of accidents in civil engineering works:
Which of the above causes are correct?
Which one of the following Acts covers provision for daily working hours, holidays and overtime payments?
What is the depth of a point below water surface in sea where pressure intensity is $1.006\text{ MN/m}^2$ and the specific gravity of seawater is $1.025$?
Which one of the following pressure gauges is most accurate device and is used for precision work and calibrating other pressure gauges?
Water is flowing through a pipe of $5\text{ cm}$ diameter under a pressure of $29.43\text{ N/cm}^2$ (gauge) and with mean velocity of $2\text{ m/s}$. What is the total head of the water at a cross-section, which is $5\text{ m}$ above the datum line? Take the density of water as $1000\text{ kg/m}^3$.
Pitot tube is one of the most accurate devices for